Atmel AT91SAM7X-EK Manual Online: Errata. E–ATARM–Mar Motherboard Atmel AT91SAMEK User Manual. (39 pages). Motherboard. 7: Only available on products with embedded Flash. 8, 10, 16, 17, 19, 20, 21, On board DataFlash chip. 9: Please check at91sam errata # Example: To compile a DataFlash boot project for AT91SAMEK board, type the following commands: 3: Please check at91sam errata #
|Published (Last):||5 February 2013|
|PDF File Size:||20.65 Mb|
|ePub File Size:||1.91 Mb|
|Price:||Free* [*Free Regsitration Required]|
Only available on products with embedded Flash 241011131415 Printed on recycled paper. For more information on this topic, please check the corresponding SAM product datasheet section Boot Program. Internal RC Oscillator On At91xam9260 pin 3: Connect to LinksToCommunities page.
These jumpers are provided for power consumption measurement use. To use the software shutdown control, J3 must be opened.
Other terms and product names may be trademarks of others. Jumpers Configuration Designation Note: Supported on SAM rev B onwards 7: You can find a valuable summary in the document named SAM9 Boot Strategies or see the cross matrix below.
AT91SAM9g20 errata datasheet & applicatoin notes – Datasheet Archive
Internal reset controller with bi-directional reset pin! Removable DataFlash card 89: In this case, J10 configuration must be set in position 1, 2. Avoid touching the component pins or any other metallic element. A grounding strap or similar protective device should be worn when handling the board. The marking should be: Choose the proper media tab DataFlash, NandFlash, etc. Other terms and product names may be trademarks of others.
To use this feature, the user has to open the strap and insert an anmeter.
Usually cross-compiler-prefix- looks like arm-linux- or arm-elf- Notes 1: Lithium 3V Battery On board DataFlash chip 3: In the linux4SAM pre-built demo it is used to configure the hardware and to at91sam2960 and start the standard U-Boot bootloader, it can also be configured to start directly the linux kernel. A GND Test point. The board must not be subjected to high electrostatic potentials. Only one available with the lead PQFP package.
Added new Section 6, Errata. Coaxial plug center positive standard. Power supply and audio! DC power is supplied to the board via the 2.
LegacyLinux4SAM < Linux4SAM < TWiki
External reset pushbutton 3. The markings for BB and 1V8 are inverted. On J10 pin 1 square pin: Newer version of AT91Bootstrap from version 1.
Two user input pushbuttons 2!
One user green LED! Added errata Section 6.
All EBI Signals of the AT91SAM are routed to extension footprint connectors J25 This allows the developer to check ay91sam9260 integrity of the components and to extend the features of the board by adding external hardware components or boards. Reproduction and publication without our written authorization shall expose offender to legal proceedings. Errta new schematics in Section 5.
The information in this document is provided in connection with Atmel products. One yellow power LED can be also software controlled 3. Refer to Section 4.
Memory Configuration on AT91SAM9260-EK board.
By default, they are closed. If S3 is closed, R13 must be unsoldered. Please check at91sam errata Dataflash memories have page size of bytes, 0x hex and the load address 0x is thus in the middle of at91sxm9260 page. AT73C clocking In the present schematics block diagram p. Board Layout – Top View!
EOLs und PCNs – Discontinued Products and Product Change Notifications
No license, express or implied, by estoppel or otherwise, to any intellectual property af91sam9260 is granted by this document or in connection with the sale of Atmel products. All material on this collaboration platform is the property of the contributing authors. Supported on SAM rev B onwards